Monitoring IoT with Graphite and Grafana: tutorial with Raspberry Pi 4

March 26, 2020

In this blog post we'll show you how to set up a Raspberry Pi 4 to be monitored by Graphite and Grafana. We'll start by setting up the device to send metrics, then we'll send the metrics over to MetricFire via StatsD and Collectd, then we'll display the information on a Grafana dashboard. If your IoT device is running on Raspberry Pi, or if it is using Linux, you can follow along with this article step by step. Even if you're using different equipment, this article will be applicable to all IoT devices using Linux.

Get started by signing up for the MetricFire free trial, where you can send metrics and visualize them in the platform within minutes. MetricFire is a service that hosts Prometheus, Graphite, and Grafana, and we'll be using it throughout this tutorial. Setting up the monitoring system with MetricFire will help save tons of setup and maintenance time.

The graph below is our final product: this panel shows the CPU usage/idle of our Raspberry Pi 4, and how many times a button has been pressed. Let's check out how we did it.

First, we will use Collectd to send CPU metrics from the Raspberry Pi to MetricFire. Then, we will use StatsD on the Raspberry Pi to send data about how many times a button is pushed to MetricFire. Once we have the information in MetricFire, we will visualize it on MetricFire’s Hosted Grafana dashboards. 

In order to follow this tutorial, we will be using Collectd installed from the Linux package manager, Python library for StatsD, and config files downloaded from the MetricFire platform. Custom config files for Collectd need to be used so that Collectd can easily connect to the MetricFire platform.

Setting up the Raspberry Pi for Monitoring

Boot the device with Ubuntu Server

First, we need to flash the micro SD card to have a bootable OS. Today we will be going with Ubuntu Server 19.10. For Windows, use Rufus (recommended). For Linux or Mac, try Etcher. Once your micro usb is flashed, plug it into your Raspberry Pi 4 and plug in the power. It will take a while to boot into the login prompt, but when you see it type in ubuntu for both the user and the password. If you are successful, it should prompt you again on changing the default password.

Set up the WiFi network

Make sure to connect the device to the WiFi using the following commands:

sudo cp

/usr/share/doc/netplan/examples/wireless.yaml /etc/netplan/


Configure font size

If you are using one of the small screens with a case add-on, initially the font size of your terminal will be pretty small. To change that, we can run the following command:

sudo dpkg-reconfigure console-setup

Leave everything on default until we get to the font size page. Put the font size on the highest setting.

Update and Upgrade

Once the wifi is working, run the following command:

sudo apt update && sudo apt upgrade 

Upgrading is important, as it’ll set up the device as a server. If you get a lock file error, either wait for that process to finish, or kill the process number that is displayed in the error if it doesn’t go away. This error occurs when you are simultaneously installing or uninstalling something, as that process will put a lock on the upgrade if it is already doing something.

Setting the Raspberry Pi up for Monitoring

Sending files from your PC to the Raspberry Pi

We will be sending files to our Raspberry Pi by SCP and by being on the same wifi network. First let’s get our wifi’s IP address with ifconfig.

If you don’t have ifconfig, use:

sudo apt install net-tools

Once you run ifconfig, remember the IP address of wlan0. Check the image below and see the red circle as a reference. We will use this IP address to send files to via SCP.

Let’s SSH into our Raspberry Pi from our main PC, so that it’s easier to work with. Run SSH ubuntu@IP_FROM_IFCONFIG and it should ask us for the Raspberry Pi’s password.

Now let’s try to SCP a file over to our Raspberry Pi 4 from our PC. 


Sending the Custom Config File from MetricFire

The easiest way to use MetricFire with Collectd is to install MetricFire’s Custom Config file on to the device you’re monitoring. The Config file can be found on the Hosted Graphite platform under the addons section. Go to the Hosted Graphite platform, click addons, click Collectd, and you will see the spot to download the custom config file

Send your custom collectd 5.4 conf file that you download from your MetricFire account with: 

scp collectd.conf ubuntu@IP_FROM_IFCONFIG:~/

Then confirm on your Raspberry Pi 4 that the file you sent is there, like in the image below.

Again, make sure your PC and Raspberry Pi are on the same wifi network in order for SSH and SCP to work.

Setting up Collectd on Raspberry Pi

We will now set up a system monitor with collectd and MetricFire. Install collectd with: 

sudo apt install collectd 

If you haven’t checked out our video tutorial  on Collectd, I suggest reading it before continuing to set up MetricFire’s Collectd on your Raspberry Pi.

After Collectd is installed, we will enable Collectd as a daemon, and then start it with:

sudo systemctl enable collectd

sudo systemctl start collectd

You can check the status of collectd with:

sudo systemctl status collectd 

Now let’s insert our Collectd config file with the custom one from MetricFire that we sent via SCP. You can overwrite the config file with the command below:

cp collectd.conf /etc/

Once the config file is in the correct place like in the image above (refer to the collectd docs to find the default directory for your own OS), the system metrics should start sending to MetricFire. Wait a bit, and then confirm on your MetricFire dashboard that the metrics are being sent. You can confirm by checking your Metric Treemap under the Metrics tab in your dashboard. 

Then quickly create a dashboard for your metrics. I made a dashboard that’s tracking CPU idle, system, and user usage.

Now we have a system monitor of our Raspberry Pi 4 running Ubuntu Server!

Setting up StatsD on Raspberry Pi

Lastly, every IoT device needs some kind of stats tracker for user usage data -  we will use StatsD to do that. In this section we’ll collect stats on how many times a button is pressed by our Raspberry Pi, and send the stats to MetricFire. Check out our article on setting up StatsD for a more detailed look at how to get StatsD running. For this example I will be using Python, so let’s install pip for Python 3 with: 

sudo apt-get install python3-pip

Next, let’s install the statsd package for Python with: 

sudo pip3 install statsd

Next, let’s make a directory for our IoT functions and create with executable permissions with: 


chmod u+x 

We’ll make a simple print function to represent a button being pressed on this Raspberry Pi. Each time we execute the button function, it will indicate the button has been pressed five times. Copy and paste the code into like in the image below, or from the code snippet. This button will have StatsD tracking how many times the button has been pressed.


Let’s press that button we just made once.

Wait a bit, and then confirm in your Metric Treemap to see if you see any new counter metrics coming from StatsD.

I spammed the button 30+ times to produce the example graph in the image below.

Now we have StatsD set up to track counters, rates, and gauges on any functions that the device has!

Ubuntu Server 19.10 on Raspberry Pi 4 — Housekeeping Tips 

If you restart or shutdown and there is a desktop environment instead of the terminal, press ctrl-alt-f2 to get back into the terminal. This shouldn’t happen if you have properly updated and upgraded the system.

To safely shutdown, type: 

sudo shutdown -h now

To reboot, type: 

sudo reboot

To scroll, use:


I hope this guide helps you set up Ubuntu Server (IoT) 19.10 and MetricFire on your Raspberry Pi 4 without much trouble. Having monitoring on your device can greatly help improve your product more efficiently.

If you're interested in trying it out on your own, sign up for the MetricFire free trial. You can monitor your Raspberry Pi without doing any installation for Graphite, Prometheus or Grafana. If you're interested in doing large scale IoT monitoring, book a demo and talk to us directly. We're always happy to get on a call and see how MetricFire can help your company.

Related Posts